Tip of the concrete for home repairs. We need to focus on the texture of the concrete is that we must try to avoid meat and concrete have been identified to occur at times in order to fill the house is not concrete in case of higher than 2 meters, or if It is necessary to concrete from as high as inevitable. We need to use a hose to pour in some cases, we use Tremie pipe rails, known as Chute and do not use a chain of concrete. That too. And added a little more. The concrete to repair the house as well. Should not be used on steel pendant. Another important part is. When concrete is to be stopped. We just need to do to correct it every time, for example, before placing concrete. An ongoing basis. We need to make the concrete surface to be rough and clean. And painted with chemical bonding. Cement slurry or water, depending on each case. To do this is to allow the concrete to be poured forth, and pour new concrete can be a completely homogeneous. We must also consider the addition of a seam to seam. Not be a cause cracks very easily. For completing it. Techniques to further concrete tips on how to fill your home correctly.
How well I really do not think it's hard to see the concept before it roughly.
The principles of good home. It's not complicated. But it does not do the same simple example we will need the space under the house to make more. For receptions.
We need a break from the concrete floor first. The main structure is anchored to the ground out of them. Then, using the structure. Reinforced steel beams. In addition to a good home for the home, or perhaps we may install steel anchor the house to the next step, we use a hydraulic jack to raise. By the various points raised by the axis of the house and then we will move at 5 cm will do this until I get high. I will continue to move up to the pole that is already raised. For some of the pillars of the old, it needs to be replaced, otherwise a good home, it is not healthy. This is the best way to completing the house. Officially
Flooding is a major problem in Thailand at the moment. We can see that my sandbag barriers at home full time. But no matter what it is. Water is still entering the house anyway. Today we will look at how to sand properly. Sand barrier does not allow water to enter my home.
- We need to prepare before the first device. Sacks of sand 2. Spade (or anything else to dig.) 3 large plastic sheet for the sandbag line.
- The digging of the trenches to lay sandbags to be about 2 sacks of sand to be placed.
- Analysis of a plastic sheet prepared to pave over the trenches to dig. The portion of the excess plastic from the front as possible.
- The sandbags are prepared. The stacked layers on plastic sheets over them. As random as we want.
- The end of a sheet of plastic folded back over onto the sand bags placed. Then remove the bag of sand layer above another.
- How to hide a bag of sand, facing toward the bag and stacked into a pyramid layer limit, then press firmly. To make the sand stick together as one flesh.
That could be your home from flood And to block sand it properly. The flooding has gone with it.
The room is painted a different color, pattern, making the room look beautiful and exotic eyes. Thanks to modern technology and interior colors available for a particular pattern. We should choose the color of the original 100 percent acrylic semi-transparent. Will result in beautiful designs. Is unique.
- From cleaning walls before painting the room (including filling cracks and leaks are completed) to the time it takes to paint a clear pattern. Not to be malformed.
- Next, paint the floor. Whatever the color you like. I have to wait at least 4 hours after applying the paint to dry before. So I created a different pattern.
- And then make a pattern like that in a different color paint on the floor. We may use the trowel to scrape off. Result in different patterns on the pattern you like, then leave to dry for at least 12 hours to finish and then start painting. The texture of trowel to make me feel confident doing this with a roller to roll vertically. Then east along 45 degrees to create a pattern. Then leave it for at least 12 hours, then apply a glaze at all. We will have a modern design appeal. We can not be applied to the roller, plain roller designs. Using a small chamois cloth placed on the rollers. This will show you how beautiful it is to use a brush to create different textures after painting a pattern as you go. If you need work done, it should be done within 10 minutes, dry the best. We can use to make molds of various designs such as flowers, etc., and if we are tired of the same color can be repainted immediately. No need to peel the paint off it.
A different pattern. Can compensate for the installation of wallpapers.
The first starts from the material before. Is to choose a color to match the surface to be used. The use of quality first. If we paint the house with the color quality is low, then it will definitely be long-lasting and beautiful. It is not possible. Here are some tips on how to paint the house the way.
1. We need to prepare the surfaces to be painted. It is a very important step. Surface preparation will be ready when the paint down. To make it homogeneous. The beauty of it is smooth before painting every time we have to clean up dust, clean the surface first. Whether it is dirt, dust or grease on the surface. May be washed with clean water if possible. Or wash with soap. If you do not provide much of anything. Then rinse with clean water. And may need to be sterilized by the fungus occurs at the surface. I have the original plaster for the walls in a way to remove old paint to rub out. If any cracks or defects must be repaired prior to completion. Once cleaned before painting to dry completely. So I started painting again.
2. Paint primer. Before using a paint brush to it. The primer will help paint the new paint adhere better to the skin. Help prevent damage from Chemical reaction between the surface of the skin. Concrete surfaces must be noted that if the new old or new concrete foundation with a new primer. To make them go out to paint a feel for the old cement floor covered with masonry paint primer. Reduces the heat of the old paint will adhere better. For wood surfaces. Use wood primer first. In order to maintain wood. And adjust the smoothness. The color and shine. For the steel surface. Primer helps the paint to stick long coat and helps prevent corrosion of surfaces.
3. For the final painting is a technique. To paint at least 2 times, each time having to wait for paint to dry completely before This is just a paint color to be beautiful and It's not long lasting.
Currently, the kitchen, we do not have to fill in the open kitchen was a big part. The principle is that we are making the kitchen and eat the same things. The kitchen is connected to the intake of rice there. The elements are clear. The same connection. It also accounts for both used in cooking. And eat. This will make the kitchen look bigger and more open. The kitchen is this way, people who eat the most beautiful and classic. We customize your kitchen as well. What is to be careful. The addition of this type can cause smoke from cooking smells and sounds, but that is another fascinating post. I do not smell at all hungry. Even if it knocked the pan with it. I can stomach it. But for those who do not like. Ventilators may be used. Or hood to reduce the problems that occur. But we also feel that more restrictive. We have a kitchen garden, it is our connection to the outside to the inside, it makes clear to another. Depending on how creative.
The exterior of the foregoing. The interior kitchen is important. I believe that in our kitchen accessories that help make our kitchen more complete. There is cleaning equipment such as the hood. And other cleaning equipment, we should do to keep these devices. I am popular, built-in. In order to see the same pieces of the kitchen. I clean it.
The addition of a garage or parking. We can do this in several ways.
1. The first we have to adjust the space before. The concert by the Spirit into the ground. In this way, we do not need to stake or beam supporting the weight. The space is tight, then we should be pouring concrete into the future. (Concrete On Ground) the addition of a garage to make cost savings and cost a lot. However, this method still has the problem is settlement of the area into the garage to fill it.
2. The second is the addition of a garage. In the pile. We can do this in several ways. Depending on the needs of home owners that want to secure your garage, how, if we plan to make room on the garage. We may use a needle to penetrate. This is expensive, but if we do not want them to roll down the needle. Which is very popular. This is a short needle hammering away about 1 meter, which is cheaper. When the needle is. (Check out the needle puncture with a needle roll), it will be concrete. Either way, this helps to prevent the settlement of the house enough.
3. The way in which the best and most expensive in the garage is filled. The same structure, making it a home. This is all packed into a beam. And the base of the house. The pile. This will pour concrete for the structure of the original house. This will allow the addition of your garage is very tight. And protection of settlement of the garage was the best.
Surfaces in the garage. Therefore focus on the rough, not smooth, rough or sand used in cement wash. And garages should be located away from the house enough. If possible, in order to prevent the slick and the accidents that can occur in various regions of the page.
To repair the roof. The first case in which the leaking so we had to try and find where the leak is not that really where it's due. If the leakage is caused by the waving of the mortar. To repair the roof. May be done as follows.
The best way to repair a roof is to be demolished, new plaster, new ways to do this is the real solution. When leakage up. To repair the roof with cement or sand it. If an overflow to the head such as cement tiles. Or cement is not good. Or not the drainage holes. Sometimes it may be due to water uptake. This is great for several reasons. After that, a new family. Then closed with PU glue. This is done by the manufacturer. And people do have the expertise to do so. It will work out better than Method 2.
2 fillings Repair cracks and paint sealants. This method does not need to be removed. First, it will be easier to use the water for about ¾ TOA cement. To repair cracks, defects. And polishing complete with finishing. Finally, skin covered with toa Roof seal sun block chemicals were applied to the entire master's roof. This allows the heat better and will reflect the heat. With the leak as well. The chemical is taken as a film coating provides flexibility really well (but be careful because these chemicals are being used).
3 ways that I recommend is to shoot the PU foam. The waterproofing PU Foam, Polyurethane Foam has been developed to solve the water problem, repair roof leaks and waterproofing works well with high-quality Polyurethane Foam is suitable for repairing leaks. This foam can stop a shot for sure. Material, the foam will expand when exposed to water is 2 parts: first and second fluid Polyurethane Foam: Foam accelerator. The nature of the foam will not shrink. And reacts with water to grow a little to prevent leakage. Flexible as well. Have good adhesion to wet and dry surfaces. Safe environment. This foam material reacts with water to control the timing of 3 minutes and 30 seconds Training waterproofing Polyurethane Foam PU Foam (Polyurethane Foam) is not toxic to the body. Can be used with potable water storage tanks. The swimming pool is safe. Without the need to keep water out how to get rid of the fog, water, cement dust and dirt and grease. Within the cracks. Penetrate the injection of water (Packer) oblique angle of 45 degrees with a hiatus in the middle of the penetration depth of the rift between drill holes and then install the game (Packer) based on them. Chemical Foam Polyurethane Foam injection pressure to a pressure greater than 17 bar into the cracks. Or where there is leakage of water through the nozzle. Foams will react with water and then Seth came out to see. Then inject a shot in the head by the installation completely. And may need to inject a boost to water leakage is completely stopped the growth of the Polyurethane Foam Polyurethane Foam trend is up about 3.15 MPa pressure should be carefully repaired.
Step 4: Use silicone to fill that this is the only way to solve. In preliminary only. Can not really solve the problem.
